ID# 177455Posted Jun 22FOR SALE $430
like the title says also have bed caps for them.
ID# 177454Posted Jun 22FOR SALE $2,449
Pro am Front hubs with 2 1/2 snout 6 on 5.5 Toyota Chevy pattern only used for mock up
ID# 177442Posted Jun 21FOR SALE $6,500ProAm 934 Midboard Hub Kits ProAm 934 Midboard Hub Kits
ProAm 934 Midboard Hub Kits 35" long 35 spline Axels new Leather boots
ID# 177439Posted Jun 21FOR SALE $5,000
2005 intimidator fabrication 4 seat buggy
Please msg me for more pics of included parts
tabbed for LS and weddle sequential either "d" or "s" box
300m axles for 934 setup
PSD updated front geometry and arms
2" hollow spindles
steering box spreader and ties rods
m&m mid board hub rear trailing arms
16gal JAZ fuel cell
brand new CNC dual brake master with balance bar (swing style) brand new CNC clutch master swing style pedal assembly
drivers seat heavy duty custom sliders
tabbed for any common seats like PRP or mastercraft
1/8" aluminum skid pan
light bar to accomidate LED setup
full center console, dash, side panels, roof panel, front inside floor pans,
trunk wing and fiberglass nose piece
I started this chassis project awhile back and poured alot of time into it
but plans changed and I went a different direction so it needs a new home. Any
visible rust is purely cosmetic and will clean up with a scotch brite pad. The chasiss will be sold as is with a bill of sale if needed. The chassis was fully assembled through the years off and on but nobody ever started the title process. its a great chassis and the back seat will accomidate 2 full sized humans with mastercraft seats. The chassis just needs a few tabs and some odd n ends but its ready for a new power plant and wiring. Needs very minimal stuff to complete, alot of the heavy fabrication and design is already complete just needs someone with the energy and parts to be able to enjoy.
ID# 177438Posted Jun 21FOR SALE $2,000Fox
-2- Fox 3.0 x 12” 3 tube bypass shocks. Just rebuilt(new seals, wear bands, and fluid) and valved for my own personal application, but I’m going a different route. Great shape. A couple blemishes on the very bottom of the shaft on both shock, but not a concern. Asking 2000obo. Feel free to text or call and I’ll send over the Valving specs. Thanks
ID# 177436Posted Jun 21FOR SALE $1,800Fox
Set of low mile Fox 3.0 bypass shocks. Rotating tops. Unknown valving. Came off a daily driver Jeep. No more than 1000 miles on them. Need a 10” shock for my application so these are too long for me.
ID# 177432Posted Jun 21FOR SALE $500
Selling a set of custom 4-1 long tube headers with 3” stainless Borla XR1 race mufflers and stainless v-band connectors. 1.75” primaries. Was used on my standard cab 1994 F150 with a 408w motor. Has mounting tabs to bolt exhaust to existing cab floor pan bolts. Header exhaust flanges are for aftermarket heads and will not fit factory Windsor heads. They have a 3” bolt spread (measurement of the holes on each side of the primaries). Everything cost me about $2000 new. Asking $500. Located in San Diego. Sorry, no shipping. Local pick up only.
ID# 177430Posted Jun 21FOR SALE $60
Selling a set of 4 Kartek black 15” limit straps. Perfect condition and only used for mock up. Bought the wrong lengths. $60 for all 4. Located in SD. Willing to ship for shipping fees.
ID# 177420Posted Jun 20FOR SALE $180
For sale is a set of 9 injectors for an LS2 with a factory fuel rail.
They have been cleaned and flow tested at ARCE racing recently, in Santee, CA. (see receipt for 200.00 for recent cleaning).
They were on my car for about one hour of drive time and I decided to go to a different fuel rail injector system which required a different height of injector.
These measure 2.9 inches in total height.
They are a factory ford designed injector with all new O-rings.
I bought one extra for a spare, there is a total of 9 injectors.
These were installed on a F.A.S.T. intake manifold.
Fuel rail has factory decal/label on it, USA. They are original quality FORD injectors.
There are numbers on the side of the injectors, they read, "0 0280 156 127" and "2R3V - B5A"
They will support up to 625 HP or will run well with a smaller 375 Hp engine.
This is a package and I will not separate the fuel rail or the injectors.
Quaility parts, install and drive, no issues, they have been carefully stored and kept in a dirt free environment.
six 1 9 - eight zero 4- 14 sixty. Tom
ID# 177416Posted Jun 20FOR SALE $1,9952020 custom 5 unl
I have a set of class 5 unlimited rear arms and Jamar Pro X brakes for sale. asking $1995.00 for the package. Might also have a few 930 cv's for sale. (Photo shows a Wilwood caliper. Arms will come with a set of Jmar Pro X calipers)
ID# 177419Posted Jun 20FOR SALE $6,000AUDI R8 LAMBORGHINI MANUAL TRANSMISSION
AUDI R8 LAMBORGHINI GALLARDO MANUAL TRANSMISSION V8 6 SPEED with LS adapter plate from SL-C and bolts, also has all the rear suspension components from SL-C (super light cars) parts come off a SL-C that was in a fire but suspension parts and transmission look to be in good condition just need a good cleaning and heims replaced. I also have the rear of the car if you want the full set up with everything else. Asking $6k for everything 7604999544
2007 Sand Limo Squirt 2- seater
Armada TT Spec / 6100
Polaris RZR XP Turbo 4
*SOLD*2016 GET Performance Mini Alpha 10 Car
JEEP GLADIATOR WITH PROCHARGER
2016 F-350 Truck *updated