New, never been bolted in a car. 930cv cups, RP in photos

I have for sale a BRAND NEW, never installed, set of Hellwig LP-25 progressive load leveling helper springs (2527). Also included is the mounting kit (25250) allowing these springs to be used with a wide range of trucks.

These will fit the following:
•2003 - 2008 Dodge Ram 1500
•2003 - 2010 Dodge Ram 2500
•2003 - 2010 Dodge Ram 3500
•2011 – 2013 Ram 2500
•2011 - 2022 Ram 3500

•2001 - 2006 Chevy Silverado 1500 HD
•2001 - 2010 Chevy Silverado 2500 HD
•2001 - 2010 Chevy Silverado 3500 HD

•2001 - 2006 GMC Sierra 1500 HD
•2001 - 2010 GMC Sierra 2500 HD
•2001 - 2010 GMC Sierra 3500 HD

•2008 - 2010 Ford F-250 Super Duty
•2008 - 2010 Ford F-350 Super Duty

Asking $400 for the kit. (New these cost $630)

Two Aluminum Fuel tanks, 40 gallons each 32" wide x 32" long X 9" tall. Never used, sold the trailer I was going to install them on. They have threaded inlet and outlet bungs welded in. Price is $350.00 each OBO

Th400 professionally built
Dyno tested

Aluminum pump body
Moly coated pump gears
Billet forward hub
300m input shaft
Billet forward drum
Billet pressure plates
4l80 direct drum
34 element Sprag
Heavy duty low Sprag
300m intermediate shaft
Rollerized planet sets (350 thrust bearings between front and rear planets and output shaft and case)
Std pattern full manual valve body
Sonnax case saver
-8 in and out fittings
New bands, clutches, seals, bushings, bearings, etc
Hard parts magnafluxed

Camburg upper arms and king 2.5 shocks
2.5” king coilovers
2.5” king piggy backs
All shocks are freshly rebuilt with new seals and bushings throughout, rear shock shafts were are replaced
Camburg upper controls arms with 1.25” uniball
Dirt king upper arm alignment cams
Also have Mazzulla front skid plate and tube bumper

Asking 3000 for shocks and arms
If you want the skid plate and bumper it’s 3500 for everything
Can install everything for additional cost
Also have 1 single 315/70-17 BFG KM3 in a method that’s brand new never been bolted on -350

Please call or txt Brett if your interested

I have 2x bilstein 16” coilovers
625$ each
- 2.5” body 16” travel
- 8125 factory valving
- Brand new never used
- never installed just opened boxes To inspect

4x bilstein 2.0 bump stops
250$ each
- 2 are 3” travel
- 2 are 4” travel
- comes with the mounting clamp tube
- brand new in box

4130 Universal Weld-It-Yourself Equal Length Beam Kits are in stock! Two kits remaining.

These kits come with ALL the required 4130 laser cut plate to build a set of beams, radius arms, race uprights, and steering arms. Also includes ALL required 1.25" rod ends/bungs for the beams/radius arms, 1.5" uniballs/cups, and machined 3/4" thick 12 bolt snout blocks. These are designed for ~91"+ track width, and can very easily be trimmed down to narrower widths. Also included are universal beam pivots, radius arm brackets, and steering swingers - all from 4130 as well.

Priced at $2699 for a full kit.

Located in Sacramento CA but can ship to the Western US for $175.

Email [email protected] to order, or text the number in the ad! By phone, please text ONLY. I get a lot of spam calls so not all calls get answered/returned, and I am unable to retrieve voicemails.


Note: tubes are not included in the above price. Rod ends for the steering are not included. Misalignment spacers for the uprights are to be provided by the customer.

This is NOT a bolt on kit. Fabrication is required, and you must know or be willing to learn how to install an equal length beam setup. Welding instructions are included, but installation instructions are not. Assembly and welding required. Must be performed by a competent professional fabricator. For off-road use only.

Super rare Addicted Desert Designs Mid-Travel Ford Raptor front suspension kit. This came off a Gen 2 Raptor. If a bombproof mid travel kit is your goal it doesn’t get beefier than this. It’s built like a tank.

It includes everything pictured:
ADD Boxed upper arms
ADD Boxed lower arms
ADD Boxed Spindles
ADD Huge tie rods
Newer Foutz fitted sway bar (~5000 miles)

This kit has all new heim joints upper and lower / spherical bearings / wheel bearings. I just did a complete overhaul on this and then decided to go full long travel.

I will pay shipping in the lower 48.

There is well over $10,000.00 in hardware here.

Asking $3500 obo

Please Call or text

Proam 2.5x6 rack. Freshly rebuilt by Pro am with 0 miles on it. Bought it for my project but ended up needing a 4.5” throw. Retails for $5500, asking $3200. *SERVO AND RELIEF VALVE NOT FOR SALE, RACK ONLY* Might be interested in trades for buggy parts?

From McKenzies website:

ProAm's 6in travel rack is built to handle vehicles equipped with up to 42" tires. Built and designed for strength, smooth responsive steering under the most extreme track conditions for ultimate steering performance. This version, 2.50" Ram size is recommended for 6100/TT type of vehicles.

SKU: TTPR6250
Rack housing hard anodized with a brilliant black finish, adding a layer of protection that decreases wear and corrosion.
Rack housing manufactured from domestic aerospace quality material
Rack bar & pinion and piston assembly are *GUARANTEED FOR LIFE* - see below*
6" Travel
2.50" Ram
1.5:1 Steering ratio
-8 AN port ram inlet fitting
3/4-36 spline steering shaft output
Made in USA