2003 Chevy Silverado 1500 project
I’ve owned and built this truck for the last 10 years
32k no motor or transmission
Front of truck -
Brand new mazulla race kit , never ran only tacked on .
Brand new mazulla race hubs
Brand new king coil overs (no bypasses but can run up to a 4.0 bypass which was the plan until planning to sell)
Brand new king bump stops
Brand new Izzy fab engine cage
Brand new triton tube connectors for engine cage x
Lewis built swing set steering
Brand new gear box
Hydroboost brake system
Lewis built front rack n pinion delete crossmember (not on truck yet , so can still run rack n pinion )
Fiberwerx glass all included
Stock core support
Brand new grill
Brand new headlights and light brackets

Izzy fab 4l80e conversion crossmember

I have a custom drive shaft to run the 4l60e but it’ll have to be shortened to run the 4l80e

Cab-
Te designs cab cage fully Tig welded
Setup for two seats and a kids seat (can be swapped for a third adult seat with modifications)
I have the two seats
Brand new fiberglass dash
Brand new pci race radio setup with kenwood upgrade

Rear of truck -
Te designs back half fully Tig welded
Te designs 60” links Tig welded
55 gallon fuel safe fuel cell mounted against cab
Fuel pump , pre filter and post filter all mounted under tank on frame rail
I have an extra fuel pump also
Setup to run two spares laying down with y straps(included)
Sway away sway bar
Has king coil overs with finned reservoirs
Can fit up to 4.0 bypass , I sold the old bypasses to get upgrade to before planning to sell
Battery mounted in the trunk with a breaker
Camburg 3.5 housing with Currie unit bearing ends , 35 spline axles, strange third member spooled with 5:14 gears , wilwood brakes

I have all the tubes to build out the trunk lid

Wheels and tires-
6 race line wheels and tires on 39” Bfg projects
I have 11 Bfg projects for it and two 37” Bfg

Misc-
I have race nets
Race horn
Race medical kit
All new oil for the motor
All new coolant
All new trans fluid
All new fluid for rear end
8 panel switch pro
New momo steering wheel
I have a ton of stuff for this truck . It is basically complete besides some mild fab work need to finish firing the 39” tires but cut enough to clear 40’s
The truck also needs a Holley terminator wiring harness and dash . I cut factory wiring out and planed to go that route for simplicity

Overall the truck does need some work but it is close and has a ton of brand new parts and already has parts on it to with stand big power and desert abuse . The truck will be a badass truck once finished and done right .

2003 Chevy Silverado 1500 project
I’ve owned and built this truck for the last 10 years
32k no motor or transmission
Front of truck -
Brand new mazulla race kit , never ran only tacked on .
Brand new mazulla race hubs
Brand new king coil overs (no bypasses but can run up to a 4.0 bypass which was the plan until planning to sell)
Brand new king bump stops
Brand new Izzy fab engine cage
Brand new triton tube connectors for engine cage x
Lewis built swing set steering
Brand new gear box
Hydroboost brake system
Lewis built front rack n pinion delete crossmember (not on truck yet , so can still run rack n pinion )
Fiberwerx glass all included
Stock core support
Brand new grill
Brand new headlights and light brackets

Izzy fab 4l80e conversion crossmember

I have a custom drive shaft to run the 4l60e but it’ll have to be shortened to run the 4l80e

Cab-
Te designs cab cage fully Tig welded
Setup for two seats and a kids seat (can be swapped for a third adult seat with modifications)
I have the two seats
Brand new fiberglass dash
Brand new pci race radio setup with kenwood upgrade

Rear of truck -
Te designs back half fully Tig welded
Te designs 60” links Tig welded
55 gallon fuel safe fuel cell mounted against cab
Fuel pump , pre filter and post filter all mounted under tank on frame rail
I have an extra fuel pump also
Setup to run two spares laying down with y straps(included)
Sway away sway bar
Has king coil overs with finned reservoirs
Can fit up to 4.0 bypass , I sold the old bypasses to get upgrade to before planning to sell
Battery mounted in the trunk with a breaker
Camburg 3.5 housing with Currie unit bearing ends , 35 spline axles, strange third member spooled with 5:14 gears , wilwood brakes

I have all the tubes to build out the trunk lid

Wheels and tires-
6 race line wheels and tires on 39” Bfg projects
I have 11 Bfg projects for it and two 37” Bfg

Misc-
I have race nets
Race horn
Race medical kit
All new oil for the motor
All new coolant
All new trans fluid
All new fluid for rear end
8 panel switch pro
New momo steering wheel
I have a ton of stuff for this truck . It is basically complete besides some mild fab work need to finish firing the 39” tires but cut enough to clear 40’s
The truck also needs a Holley terminator wiring harness and dash . I cut factory wiring out and planed to go that route for simplicity

Overall the truck does need some work but it is close and has a ton of brand new parts and already has parts on it to with stand big power and desert abuse . The truck will be a badass truck once finished and done right .