Advertising supports this site
    Pre-Runners 

2003 Chevy Silverado 1500 linked prerunner

Hesperia, CA$45,000.00 OBO
For Sale

  (2) jason endsley   Private Message
 (760)995-0440   (760)995-0440
 More listings by jason endsley


2003 Chevy Silverado 1500 project
I’ve owned and built this truck for the last 10 years
Front of truck -
Brand new mazulla race kit , never ran only tacked on .
Brand new mazulla race hubs
Brand new king coil overs (no bypasses but can run up to a 4.0 bypass which was the plan until planning to sell)
Brand new king bump stops
Brand new Izzy fab engine cage
Brand new triton tube connectors for engine cage x
Lewis built swing set steering
Brand new gear box
Hydroboost brake system
Lewis built front rack n pinion delete crossmember (not on truck yet , so can still run rack n pinion )
Fiberwerx glass all included
Stock core support
Brand new grill
Brand new headlights and light brackets

Motor-
4.8 freshly rebuilt , no miles and not even first start up
Btr truck Norris cam
Ls7 lifters
Ls1 head gaskets
Ls1 rocker arms with upgraded trunions and beehive springs
I have an aftermarket intake and the stock intake
Fms 550cc injectors
All new lifter rods , seals and hats
Melling high volume oil pump
New water pump
New timing chain
All new gaskets
New thermostat
New knock sensor and siliconed shut to avoid issues
Long tube headers with y pipe
Brand new mishimoto aluminum radiator
Brand new derale power steering cooler and or oil cooler


Transmission-
I have a rebuilt 4l60e
All upgraded clutches
Upgraded gears
Corvette servo
Shift kit
Brand new Circle d torque converter 3000 stall
I have a winters shifter brand new . Just gotta install the ball into the valve body to use
Brand new derale trans cooler

I also have a 4l80e that I was told was good but I’d say use as a core and have it rebuilt and or checked rather than trusting someone else haha
I also have a Izzy fab 4l80e conversion crossmember

I have a custom drive shaft to run the 4l60e but it’ll have to be shortened to run the 4l80e

Cab-
Te designs cab cage fully Tig welded
Setup for two seats and a kids seat (can be swapped for a third adult seat with modifications)
I have the two seats
Brand new fiberglass dash
Brand new pci race radio setup with kenwood upgrade

Rear of truck -
Te designs back half fully Tig welded
Te designs 60” links Tig welded
55 gallon fuel safe fuel cell mounted against cab
Fuel pump , pre filter and post filter all mounted under tank on frame rail
I have an extra fuel pump also
Setup to run two spares laying down with y straps(included)
Sway away sway bar
Has king coil overs with finned reservoirs
Can fit up to 4.0 bypass , I sold the old bypasses to get upgrade to before planning to sell
Battery mounted in the trunk with a breaker
Camburg 3.5 housing with Currie unit bearing ends , 35 spline axles, strange third member spooled with 5:14 gears , wilwood brakes

I have all the tubes to build out the trunk lid

Wheels and tires-
6 race line wheels and tires on 39” Bfg projects
I have 11 Bfg projects for it and two 37” Bfg

Misc-
I have race nets
Race horn
Race medical kit
All new oil for the motor
All new coolant
All new trans fluid
All new fluid for rear end
8 panel switch pro
New momo steering wheel
I have a ton of stuff for this truck . It is basically complete besides some mild fab work need to finish firing the 39” tires but cut enough to clear 40’s
The truck also needs a Holley terminator wiring harness and dash . I cut factory wiring out and planed to go that route for simplicity

Overall the truck does need some work but it is close and has a ton of brand new parts and already has parts on it to with stand big power and desert abuse . The truck will be a badass truck once finished and done right .







.
    Pre-Runners   Listing #211855   Posted: Oct 07 Expires: Oct 16